Object Framing
Price range: $1.50 through $15.00
Replacement carbon spars for each frame component of the Object dual line kite, all pre-cut for easy installation.
Description
Object SUL Frame
- Leading Edge: Dynamic T8 (72.5 cm  |  2x 7 cm ferrule)
- Bottom Spreaders: Dynamic T10 (65 cm  |  1x 16 cm ferrule)
- Spine: Dynamic T12 (80 cm)
- Top Spreader: 5mm solid carbon (51 cm pre-cut)
- Stand Offs: 3mm carbon (27 cm pre-cut, complete)
Object STD Frame
- Leading Edge: Dynamic T12 (72.5 cm  |  2x 7 cm ferrule)
- Bottom Spreaders: Dynamic T15 (65 cm  |  1x 16 cm ferrule)
- Spine: Dynamic T12 (80 cm)
- Top Spreader: 5mm solid carbon (51 cm pre-cut)
- Stand Offs: 3mm carbon (27 cm pre-cut, complete)
Object VTD Frame
- Leading Edge: Dynamic T12 (72.5 cm  |  2x 7 cm ferrules)
- Bottom Spreaders: Dynamic T15 (65 cm  |  1x 16 cm ferrule)
- Spine: Dynamic T12 (80 cm)
- Top Spreader: 5mm solid carbon (51 cm pre-cut)
- Stand Offs: 3mm carbon (27 cm pre-cut, complete)
Fitting Guide (parts can be found here – list is for a complete kite)
Most breakages in the field allow you to simple swap over the existing fittings onto replacement rods but if you wish to make a ready to install spare for your kite bag, these are the accompanying fittings for each spar:
- Leading Edge
Upper – 2x Dynamic ferrule (7 cm), 2x upper spreader APA, 2x c-clip stopper, 2x vinyl end cap, 2x yo yo stopper (claw), 2x zip tie.
Lower – 2x lower spreader APA, 4x c-clip stoppers, 2x wing tip spike. - Bottom Spreaders – 1x Dynamic ferrule (16 cm) between two spreaders (glued into one side), 2x stand off fittings (one on each bottom spreader).
- Spine – 1x center T fitting, 1x tail weight fitting, 2x c-clip stoppers, 1x vinyl end cap.
Additional information
| Weight | .60 oz |
|---|---|
| Dimensions | 31 × .5 × .5 in |
| Spar Options | Dynamic T10, Dynamic T12, Dynamic T15, Dynamic T8, Ferrule – 16 cm (bottom spreader), Ferrule – 7 cm (leading edge), Solid Carbon 5mm – 51 cm (top spreader), Stand Off |
Reviews (0)
Related products
Fittings for the bottom spreaders of the Gaze, connecting them to the stand offs when assembled. Sold individually.
T fitting used at the bottom of the Gaze spine, complete with 15g + 5g weights.
Spike (or "nock") end cap used on the wing tip of the Gaze, complete with tensioner line - designed to provide good tip stabs even on firm earth or hard packed sand.
Center T fitting used the bottom spreaders of the Gaze connect with the spine when assembled.
Built for our most active customers, the L3 Clips are designed for use at the three Sync Bridle points which may see wear on the leading edge material of either the Djinn or Djuice with aggressive use. Once installed, the leading edge spar can still slide through easily with the bridle and leading edge material fully protected in those areas. These will also fit most other quad line kites with similar bridle attachments (frequently the center point). Check out the installation tutorial below!
This product has multiple variants. The options may be chosen on the product page
Angled fittings for the leading edge of the Gaze, connecting them to the upper and lower spreaders when assembled.
This product has multiple variants. The options may be chosen on the product page
One ferrule, the joint used to connect the Radius spars in the Gaze leading edge (8cm) or bottom spreaders (12cm).
This product has multiple variants. The options may be chosen on the product page
Reviews
There are no reviews yet